How to test a PCB with a multimeter
A digital multimeter (DMM) is the first instrument you reach for on almost every dead board. Used properly, it tells you whether power reaches a regulator, whether a trace is broken, whether a rail is shorted to ground, and whether a diode or IC pin is blown. Used in the wrong mode — or on a live circuit — it lies or blows its fuse.
DEADBOARD models a 6000-count handheld multimeter with real-world behaviour: a 10 MΩ input impedance in voltage mode, probe lead (0.2 Ω) and contact resistance (0.02–0.6 Ω) in ohms mode, a ~1 mA (3.0 V open-circuit, OL above 2.5 V) diode test, and honest in-circuit capacitance limits.
The five multimeter modes on a repair bench #
| Mode | Board power | What it puts on the probes | What a good vs. bad reading looks like |
|---|---|---|---|
DC Voltage (V⎓) |
ON | High-impedance voltmeter (10 MΩ to black lead) |
Exact rail voltage (3.30 V, 5.00 V); 0.00 V past a break or dead regulator |
Resistance (Ω) |
OFF | Low test voltage (~1 V) + range-dependent test current |
~0.2–1.0 Ω across intact copper (< 30 Ω beeps); OL across an open trace or cold joint |
| **Diode (`•◄ | `)** | OFF | ~1 mA constant current (3.0 V open-circuit; OL above 2.5 V) |
Capacitance (CAP) |
OFF | Ramp test current up to 1.0 V across probes |
Accurate for isolated caps; reads high or OL in-circuit due to parallel caps/resistance |
Current (10 A) |
ON (series) | ~0.01 Ω shunt between probes |
Must be wired in series with the load; never place across VCC and GND (blows fuse > 10 A) |
1. DC Voltage (V⎓) — Power ON #
Voltage is always measured across two points while the circuit is energized:
- Put the Black probe (
−/COM) on a known Ground (GND) pad or test point. - Touch the Red probe (
+) along the power path, one node at a time (VIN→ fuse → switch → resistor → LED or regulator). - Where voltage drops from
5.00 V(or3.00 V) to0.00 Vbetween two pads that should share copper, the open fault sits between them.
Watch out for 10 MΩ meter loading #
A real multimeter is not an infinite-resistance ideal probe; standard handheld meters present 10 MΩ across their probes. On low-impedance power rails or 10 kΩ dividers, 10 MΩ shifts the reading by less than 0.1%. On high-impedance bias or sense networks (1 MΩ–10 MΩ resistors), the meter itself forms a parallel divider to ground and pulls the measured voltage down noticeably — just as it does on the DEADBOARD bench.
2. Resistance (Ω) & Continuity — Power OFF #
Golden rule: Always turn bench power OFF (
Pon DEADBOARD) and let bulk capacitors discharge before switching toΩ,Diode, orCAPmode. External voltage on a powered rail fights the meter's~1 Vtest source, producing false readings (even negative or bogus values) and risking damage to a real meter.
- Continuity & broken traces: When both probes sit on the same unbroken copper net, a 2-wire meter reports lead + contact resistance (typically
0.2–1.5 Ω, beeping below~30 Ω). If there is a hairline trace crack or an open cold solder joint between the pads, the meter readsOL(Open Loop). - In-circuit resistance reads lower: Measuring a
10 kΩresistor still soldered onto a board often reads less than10 kΩbecause parallel paths through other components and semiconductor junctions conduct part of the meter's~1 Vtest current. Only trust an exact resistor measurement if parallel paths are open or you lift one leg of the part.
3. Diode Mode (•◄|) — Power OFF #
Diode mode pushes a tiny constant current (~1 mA) from the Red (+) probe to the Black (−) probe and displays the forward voltage drop:
- Testing discrete diodes and LEDs: Put Red on Anode (
+) and Black on Cathode (K, marked by a band on diodes or a flat rim / silkscreenKon LEDs).- Standard silicon diode (
1N4007):~0.60–0.70 Vforward,OLreversed. - Schottky diode:
~0.20–0.35 Vforward,OLreversed. - Red / yellow / green LED: glows dimly and drops
~1.7–2.2 Vforward;OLreversed. - Blue / white LED (
~2.7–3.2 Vforward drop): many handheld meters (including DEADBOARD's6000-count DMM, which readsOLabove2.5 V) do not have enough compliance voltage to turn on a blue or white LED and showOLboth ways. A high-compliance bench meter (> 3.2 V) or a current-limited5 Vsupply + resistor is needed to test them. - Reads
~0.000 Vboth ways: shorted diode or a parallel short across its pads. - Reads
OLboth ways (on a silicon diode or red/yellow/green LED): open/blown junction or broken trace.
- Standard silicon diode (
- Checking IC pins to Ground (red-on-ground convention): Technicians often put Red on
GNDand probe signal or data pins with Black to forward-bias the chip's internal ESD protection diode to ground. A healthy pin typically shows~0.4–0.7 V;0.000 Vindicates a dead short on that pin.
4. Capacitance (CAP) & Current (10 A) #
- Why capacitance reads high — or
OL— in circuit:- Every decoupling capacitor wired between
+3V3andGNDsits in parallel. Probing across a single100 nFceramic capacitor on a3.3 Vrail measures the sum of all capacitors on that rail (C_total = C1 + C2 + ...), which can read tens or hundreds of microfarads. - Any parallel load resistance across the rail steals part of the meter's charging ramp current, inflating the reading further — or, if parallel resistance is low enough (
< 10 kΩ), preventing the ramp from reaching1.0 Vat all so the meter readsOL. To measure a single capacitor's true value, lift at least one end off the board first.
- Every decoupling capacitor wired between
- Current (
10 A) works only in series: In current mode, the meter places a tiny~0.01 Ωshunt directly between the probes. Placing it across+5VandGNDcreates a dead short and blows the meter's internal fuse (> 10 AshowsOLin DEADBOARD). Break the circuit (for example across an empty fuse footprint) so load current flows through the meter — and on a real meter, always move the red lead back to theV/Ωjack immediately afterwards!
5. Ohm’s Law, Voltage Dividers & Resistor Codes #
Two equations solve most DC analog and indicator-circuit faults:
- Current-limiting resistor (Ohm’s Law):
I = (Vsupply − Vled) / R→R = (Vsupply − Vled) / IExample: A blue LED drops~3.0 Von a5.0 VUSB rail. With a wrong100 kΩresistor fitted, current is(5 − 3) / 100,000 = 0.02 mA(LED stays dark). Swapping to150 Ωgives~13 mAand lights it cleanly. - Voltage divider:
Vout = Vin × R2 / (R1 + R2)Example: WithVin = 5.0 VandR1 = 10 kΩ,R2 = 10 kΩproduces2.50 Vat the midpoint. IfR2(the lower resistor toGND) is missing or cold-jointed, nothing pulls the midpoint down andVoutsits at5.00 V. IfR2is mistakenly1 kΩinstead of10 kΩ,Voutsags to5 × 1 / 11 ≈ 0.45 V.
Reading resistor values (4-band colour code & SMD markings) #
For 4-band through-hole resistors, read toward the tolerance band (Gold ±5% or Silver ±10%) on the right:
| Colour | Digit (Bands 1 & 2) | Multiplier (Band 3) | Tolerance (Band 4) |
|---|---|---|---|
| Black | 0 |
× 1 Ω |
— |
| Brown | 1 |
× 10 Ω |
±1% |
| Red | 2 |
× 100 Ω |
±2% |
| Orange | 3 |
× 1 kΩ |
— |
| Yellow | 4 |
× 10 kΩ |
— |
| Green | 5 |
× 100 kΩ |
±0.5% |
| Blue | 6 |
× 1 MΩ |
±0.25% |
| Violet | 7 |
× 10 MΩ |
±0.1% |
| Grey | 8 |
— | — |
| White | 9 |
— | — |
| Gold | — | × 0.1 Ω |
±5% |
| Silver | — | × 0.01 Ω |
±10% |
- Common 4-band examples:
Brown-Black-Brown-Gold=10 × 10 = 100 Ω·Brown-Green-Brown-Gold=15 × 10 = 150 Ω·Orange-Orange-Brown-Gold=33 × 10 = 330 Ω·Brown-Black-Red-Gold=10 × 100 = 1 kΩ·Brown-Black-Orange-Gold=10 × 1k = 10 kΩ·Brown-Black-Yellow-Gold=10 × 10k = 100 kΩ. - 5-band (
1%) resistors: Read three digits first, then the multiplier on band 4 (for example150 ΩisBrown-Green-Black-Black-Brown). - SMD resistors on modern boards: Printed with 3 digits (
103=10 × 10³ = 10 kΩ,472=4.7 kΩ),Ras a decimal point (4R7=4.7 Ω), or left unmarked on tiny0402/0201packages (check the BOM or Schematic).
Practice these skills on the bench #
- First Light — Voltage (
V⎓) vs. Continuity (Ω) on a broken trace - One-Way LED — Diode mode (
•◄|) and LED polarity - Resistor & Ohm’s Law — Reading colour bands and swapping a wrong resistor
- Voltage Divider 101 — Probing test points and populating
R2 - The Sagging Rail — Multi-layer
Voutdiagnosis and resistor repair