How to find a short circuit on a PCB
A shorted power rail is one of the most common reasons a board refuses to power on — and one of the easiest to make worse if you guess. A tiny 0402 ceramic capacitor (MLCC) cracked by flex or voltage stress can pull an entire 3.3 V or 19 V rail straight to ground, leaving dozens of parts on the same net reading < 1 Ω.
Pulling capacitors at random destroys pads. Instead, combine rail splitting, current-limited voltage injection, and thermal localization.
1. Tell a short apart from a leak or an open circuit #
Measure resistance to GND with power OFF (and capacitors discharged), and watch the bench power supply under a safe current limit:
| Symptom | Resistance to GND |
Bench supply behaviour | Likely cause |
|---|---|---|---|
| Open circuit | OL or normal high impedance |
0.0 mA draw |
Cut trace, cold joint, blown fuse, open switch, dead input regulator |
| Dead short | < 2 Ω (often 0.2–0.8 Ω including probe leads) |
Immediately hits Current Limit (CC); rail collapses near 0 V |
Shorted MLCC, solder bridge, copper sliver, shorted IC/MOSFET |
| High-resistance leak | Tens to hundreds of ohms (lower than known-good) | Elevated current draw; rail sags or regulator gets warm | Liquid-damage residue, leaky capacitor, partially damaged silicon |
2. Never replace a blown fuse before finding why it blew #
Fuses do not fail from age — they melt open to stop a downstream short from burning traces or catching fire. When you find an open fuse (F1), split the board:
- With power OFF, measure resistance from
GNDto both pads of the blown fuse (F1.1andF1.2). - The input side (
F1.1) should read high impedance; the downstream rail side (F1.2) reads near0 ΩtoGNDwhile the short is still present. - Clear the short first, confirm resistance to ground returns to normal, and only then solder a fresh fuse.
On multi-rail boards without a fuse on the shorted rail, series inductors (such as a buck converter's output inductor) or 0 Ω jumpers act as natural split points: lifting one pad tells you whether the short lives on the regulator side or the load side.
3. Current-limited bench supply vs. voltage injection #
DEADBOARD's Bench menu gives you two distinct ways to use a bench power supply — mirroring real repair work:
A. Current-limited bring-up (Board PSU + Current limit) #
When powering a board through its normal input connector (100 mA or 500 mA limit), capping current prevents an upstream short or reversed diode from popping a new fuse or burning copper while you measure voltages and check thermal rise.
B. Direct Voltage Injection (Inject 1 V · 3 A or Inject 3.3 V · 1 A) #
When dozens of capacitors and chips share a dead-shorted rail, every pad on that rail measures roughly the same ~0.3 Ω to GND. You locate the fault with heat (P = I²R): the tiny shorted component concentrates power dissipation and warms up first.
Follow these strict rules before injecting voltage onto a shorted net (in DEADBOARD, place the Red probe on the shorted net, Black on GND, and pick an injection preset in Bench → Supply):
- Always start low (
1.0 V), never high (12 V/20 V). Even on a5 Vor12 Vrail — and especially on1.0 V–3.3 Vlogic rails — inject1.0 Vfirst. If a shorted MLCC suddenly burns open mid-test, or if the short sits behind trace resistance, a high injection voltage will snap the rail up and destroy every IC on that net. - Why
1 V · 3 Aheats a dead short when100 mAwill not: On a0.2 Ωdead short across a wide copper ground plane,100 mAdissipates only0.1² × 0.2 = 2 mW— invisible under copper heat sinking. At2–3 A(1.0 V),P = I²Rputs~0.8–1.8 Wdirectly into the0402capacitor or silicon fault, creating an unmistakable hot spot. (Only raise voltage to3.3 Vif the rail is rated for≥ 3.3 Vand1.0 Vdraws too little current on a high-resistance leak.) - Never inject blindly into a primary input bus (
VIN/19 V/PPBUS_G3H): First checkΩbetween the main input bus and every buck converter's output inductor (SW/VOUT). If a buck's high-side MOSFET is shorted internally, the input rail is wired straight to a1 VCPU/GPU core — injecting3.3 Vor more into the input rail sends lethal voltage straight into the processor!
4. Thermal camera traps: why shiny solder looks cold #
An infrared (IR) thermal camera measures emitted thermal radiation and converts it to temperature assuming a fixed surface emissivity (ε).
| Surface on a PCB | Typical emissivity (ε) |
What the IR camera shows |
|---|---|---|
| Matte solder mask & black IC epoxy | ~0.90 |
Accurate surface temperature |
| Exposed copper via | ~0.60 |
Reads noticeably cooler than reality |
| Bare shiny solder / metal shield | ~0.10–0.30 |
Reflects the ~25 °C room! A 90 °C solder joint can read < 35 °C |
Takeaway: Watch the matte solder mask and epoxy bodies of parts rather than bright solder fillets or metal shields. (On a real metal shield can, technicians stick a piece of matte tape or coat it with rosin/IPA so it stops acting like a mirror. DEADBOARD models this exact grey-body emissivity physics.)
5. Three bench-top ways to pinpoint the hot part #
Even without a thermal camera — or when shiny solder hides heat — three classic bench methods locate a hot short under current-limited power:
- Freeze spray (
9): Frosts an area down to0 °C. Once power is applied, the hottest component pays off the frost's latent heat first and defrosts clear while its neighbours stay white. - Isopropyl alcohol / IPA (
0): Wets the board with a thin film of liquid. Under power, IPA evaporates rapidly off the hot component first. (IPA is flammable: keep it to low-voltage DC bench work, well away from400 °Chot air or irons, and let it dry. Scrubbing with IPA also dissolves conductive liquid-damage residue!) - The Rosin method (
R): A light white haze of condensed gum rosin is applied over the suspect area (with fume extraction on a real bench). Around60–70 °C, the rosin melts clear and glossy on the hottest part first — pinpointing a single0402capacitor sitting next to twenty identical neighbours.
6. Hidden shorts: copper slivers & liquid residue #
Not every short lives inside a component:
- Solder bridges (
4Wick): Excess solder spanning two adjacent pads or IC pins. Always flip the board (F) to inspect the bottom side too. - Hairline copper slivers (
7Trace cutter): Manufacturing defects or scraped mask bridging a power trace to a neighbouring ground trace. Cut the sliver cleanly and re-checkΩtoGND. - Liquid residue (
0IPA): Dried drink/flux/corrosion residue creates conductive leakage paths across fine-pitch pins (tens or hundreds of ohms rather than0 Ω). Scrub with IPA before replacing chips.
Practice short hunting on the bench #
- Solder Bridge 101 — Spotting
~28 mAcurrent draw and wicking a bridge - Ghost Short — Splitting a board at a blown fuse (
F1) and cutting a copper sliver - Smoke Test — Using
100 mAcurrent limit + Thermal / Diode mode before replacingF1 - Olimex ESP32-C3 — Hunting a warm rail problem on a real 49-part board
- Rana Tadpole V2 — Finding why the middle of a 147-part controller gets hot
- MNT Reform 2 — Diagnosing a dead
3.3 Vrail on a 522-part laptop mainboard